Dana 18 Input gear.

78304CJ-7

I need the input gear from a Dana 18 must be 29 teeth, 6 splines, with a 1.375‚Äù shaft. Anyone???? MC you gotta have one somewhere 8) -RJ

jeepsr4ever

i can get you a new one for just over cost in jan if you can wait till the middle of jan! I dont have a case i want to tear apart or a bullgear

78304CJ-7

What kind of green we talking here..... I guess i acutally need some other gears as well.. I want to convert one of my D20 to the lower range I happened upon a Broco D20 so I am half way there. I guess I need some more gears I gott take the thing aprt to see what I have... I was looking at this :

http://www.jeeptech.com/convxfer/2.46-20/

and this:

http://www.off-road.com/_jweed/transfer.htm

Let me know...

-RJ

fuzz401

i have some old cases around would have to look and see what i have will look next week

mrtazwrench

I HAVE A CASE ON A 3SPD FROM A 74 CHEROKEE, WOULD IT HAVE ANYTHING YOU NEED?

78304CJ-7

Fuzz let me know.... there area few gears I need apparently.

mrtazwrench, I think that would be a D20... not sure though, is there a drum brake on the back of the T-case?

Does it look like this?

Easy way to tell, is the rear dif centered Cherokee..... I am pretty sure that will be a D20 already got two of them.

Mudrat

78304CJ-7 wrote
I guess I need some more gears I gott take the thing aprt to see what I have... I was looking at this :
http://www.jeeptech.com/convxfer/2.46-20/
and this:
http://www.off-road.com/_jweed/transfer.htm
Let me know...

-RJ

I like te "Almost painless" caveate :shock:

Mudrat :razz:

78304CJ-7

Yeah.... so far not too bad. I need two gears to compleate the conversion: 18 8 23 18 8 22 MC I know they can be had aftermarket let me know if you can get them and I will send some money your way. Good used ones work too 8) -RJ

jeepsr4ever

I will be able to get them cheap new in jan untill then you may find one of these guys have a used set..........but if you can wait i will order them for you in jan :(:

78304CJ-7

MC sounds fine with me, I'm not in any huge rush to do this. When in Jan, like in a week or 5 weeks? Let me know as this has been a fun project and I look forward to working on it besides it is taking up valuable space on my bacement floor :!: . I need to get my 401 out and start working on it. Then I gotta get my NV4500 going.

jeepsr4ever

BASEMENT FLOOR :shock: ............... :mrgreen: 2nd week in jan my man :sa:

78304CJ-7

Yeah the floor, so many things going on, T-18 apart, one t-150,two D20's apart, 304,360,401 3 sets of heads (not including the long blocks) ...... and the list goes on... Oh yeah mildon oil pan, offy covers, few intakes, 3 401 cranks, 2 sets of 401 rods, lp2381 forged pistons (used .030 over if someone is intreested) I am sure I missed alot of stuff not to mention all the tools.....you get the point it is a "jeep" thing after all. Merry Christmas all -RJ

jeepsr4ever

I am always looking for 401 stuff, let me know what and how much

78304CJ-7

Well if you need anything let me know... .Like I said I got about a spare everything but a block, and well if I get a good tax return aluminum (block) is in the future..... but all depends on uncle sam. I am not looking to sell any of it but I know you are an AMC diehard like myslef and other here (fuzz) and I am always looking to further the cause.... if you need something let me know I alway want to help a brother out... especially when I have been drinking (like now 8) ) You are there to further the AMC/Jeep cause and not make a quick buck off it, trying to make a living yes, but not out there to screw Joe Smoe and for me that goes along way.... ok I gotta go to bed. :razz: tooooooooooooooooo many beers :!: -RJ

thigh19

Talk to Ryan at http://www.the-jeep-guy.com/

tufcj

There's an 18-8-23 on ebay this morning....

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=34208&item=7904422948&rd=1

Bob.
tufcj

78304CJ-7

Thanks I picked one up along time ago, and actually no longer own the T-18/D20 combo. PLans are now NV4500 D300 combo. :t: -RJ